0102030405
Small Cabinet Locks Solenoid Lock For Smart Lockers
DEWOD S series electromagnetic locks are available in a variety of styles and support customization. They are widely used in various smart express cabinets, fresh food cabinets, lockers, etc. After actual market use tests, they have low failure rates and stable performance.
Used with our electromagnetic lock control board, touch screen, etc., we provide warranty for the entire electronic kit.
If you need customization, please contact us.
|
XG-S160 Electromagnetic lock parameter |
|
| Dimension: | 80mm*59mm*13.1mm |
| Way of working: | The door is closed (power off) to lock, and the power on (12V) instantly triggers the unlocking mode. |
| Emergency unlocking: | The lock body is equipped with an emergency unlocking method, and the cabinet can be locked without damaging the cabinet in an emergency. If according to the mechanical key, it can also be unlocked externally with the key, the operation is simple and convenient; |
| Energy saving: | The power-on time at the moment of unlocking is 200ms-300ms, usually when the door is closed and locked, it does not consume power and the voltage is 12V; |
| Life test: | 60,000 to 70,000 tests at room temperature |
| Elasticity: | Weak: suitable for cabinet doors of around 15CM*15CM |
| Middle: Suitable for cabinet doors around 30CM*30CM | |
| Strong: suitable for cabinet doors around 50CM*50CM | |
| PS: The default is a strong specification, and the elasticity is 14.7N. The applicable specification is based on the material of the general express cabinet door. The specific elasticity requirements should be subject to the actual test results. | |
| Applicability: | No front and back design, all sizes of cabinets for left, right, upper and lower door opening directions can be used. |
| Safety: | Sensitive, shockproof, anti-mite, anti-rust. |
| Line order: | The red and black wires are the electromagnet power wires, and the white and yellow wires are the micro switch signal wires. |
| Electrical parameter list: | |
| Voltage: 12V（Support customized, need large MOQ） | |
| Current: 2A±0.2A | |
| Resistance: 6Ω±0.5Ω | |
| Electromagnet life: more than 1 million times | |
| Key component inspection standards: | |
|
Part name |
Materials used and related technical requirements |
| Torsion spring | Made of carbon steel |
| Tahuang | Using piano steel wire electroplated white zinc |
| Electromagnet shaft core and electromagnet mounting plate pressure riveting shaft | Using DT4 electrical soft iron material, the surface I s electroplated with environmentally friendly blue zinc, and the salt spray test is required to reach above 48H |
| Electromagnet plastic shaft | Using PA66-GF30% flame-retardant material, it is required to store at high temperature +80° and low temperature -30° for 24 hours; the product has no deformation or cracking; |
| The bottom cover of the lock and the upper cover of the lock | Using cold-rolled sheet material, the surface is electrophoresed and blackened |
| Lock middle frame | Use ABS plastic |
| Lock hook | Using powder metallurgy materials, the surface is blackened. |
| Limit switch | Using shrapnel type micro switch, life test is required to reach more than 100,000 times |
| Coil insulation tape | It is required to withstand a temperature of 100°, and the tape can be melted, but it must not burn. |
| Assembly and related parameters; | |
| A. Use SM-2R male/female standard wire connection, the exposed length of the lead is not less than 150mm (including terminal); (The length of the wire and various types of plugs can be customized according to customer needs) | |
| B. The micro switch is normally closed when the door is closed; (can be customized according to customer requirements) | |
| C. Working temperature -30° to +80°, relative humidity 20%-80%; | |
| D. Storage temperature: -30° to +80°, relative humidity 20%-80%; | |
|
XG-S160 Installation size 
|
|
| Remarks: The tolerance of the above dimensioning tolerance is 1mm-20mm, the tolerance is ±0.2mm; the tolerance of 21mm-50mm is ±0.3mm; the tolerance of 51mm-100mm is ±0.5mm | |
| 5. The overall requirements of the electromagnetic lock; | |
| A. The surface of the electromagnet lock should be clean, have good luster, no bubbles, scratches, scratches, etc., the lead end should be flat, and the insulating sleeve should be complete without cracking; | |
| B. The electromagnetic lock lead-out wire and the lead-out terminal shall be firm and reliable, and no loose or loose appearance shall occur. The insulating sleeve shall cooperate well with it; | |
| C. The welding of the stroke switch and the electromagnet should be even and full, and there should be no such phenomenon as virtual welding and continuous tinning; | |
| D. After the electromagnetic lock is assembled, the functional components require flexible rotation, and there is no failure phenomenon such as stuck; | |
| E. After the electromagnetic lock cover screw is locked, there must be no screw locking and sliding phenomenon; | |
Mainly used in express cabinets, rental cabinets, storage cabinets, tool cabinets, sales cabinets and other smart cabinets.
S160 Lock Specification
